Hot Rod Black Paint, Satin 2K Urethane, 4:1 Gallon Kit w/Activator, SMR-207/211 For Sale

This sale is for a gallonof satin finish Hot Rod Black Paint(SMR-207)anda quart of activator; which yields 1.25 gallons sprayable.

The SMR-207 is a 4.8 lbs/gallon voc (National Rule product). Not for sale in 2.8 lbs/gallon voc areas like California.

SMR-207 Hot Rod Black is a 2 component acrylic urethane coating. It mixes 4:1 with a 5-10% optional
reduction with Urethane Grade Reducer. SMR-207 Hot Rod Black is an excellent coating for High Quality Black satin Finish.

This coating is formulated to withstand the same atmospheric conditions as a high qualitysingle stage urethane topcoat.

FEATURES:

.True 2K Urethane Durability

.Uniform Jet Black Color
.Excellent Exterior Stability from UV Light

.Fast Dry
.Easy 4:1 Mix Ratio

.Chemical Resistant Finish
.Great Rub Resistance

MIX RATIO:

SMR-207 is activated with SMR-211 (Speedo-Line Multi Use Activator) at a 4:1 mix ratio wit a 5-10% optional
reduction with Urethane Grade Reducer.

4 Parts SPEEDO-Line HOT ROD BLACK
1 Part SPEEDO-Line ACTIVATOR
5-10% (Optional) URETHANE GRADE REDUCER

GUN SETUP

Fluid Tip psi
HVLP Spray Gun 1.3 – 1.4mm 8-10 psi
Conventional Gravity Feed 1.3 – 1.4mm 25-30 psi

SURFACE PREPARATION:
Surface should be cleaned of all grease, oil, dirt, rust, etc before applying SMR-207 Hot Rod Black. Wash
area with soap and warm water. Thoroughly clean area with Wax and Grease Remover. Scuff surface with a red scuff pad or equivalent. Reclean with wax and grease remover. Do not use coarse grit sandpaper. Apply a pre-treatment primer and allow to dry. Apply primer surfacer and allow to cure. Sand primer
surfacer with 180-220 grit sandpaper. If applying a sealer over the primer surfacer, finish sand with 320-400
grit sandpaper. If applying SMR-207 Hot Rod Black directly over the primer surfacer, finish sand with 400-500 grit sandpaper.

APPLICATION

Apply 1 full wet coat followed by 1 medium wetcoat. Allow 5-10 minutes flash time
between coats.

Dry Times:

Dust Free: 5-10 minutes depending on temperature and activator selection
Tack Free: 5-10 minutes
Force Dry: 10 minutes @ 120°F (49°C)
Delivery: Air Dry: 6-8 hours
Bake: After cool down

Time to stripe:

Air Dry 6-8 hours (special care should be taken for first 24 hours)
Bake 1 hour after cool down

Time to decal:

Air Dry 24 hours
Bake 24 hours

Time to recoat

Air Dry 24 hours @ 70°F
Bake After cool down

Health and Safety:

See Material Safety Data Sheet and labels for additional safety information and handling instructions.

*
The contents of this package may have to be blended with other components before the product can be used. Before opening the packages, be sure you understand the warning messages on the labels and MSDS’s of all components, since
the mixture will have the hazards of all its parts.
* Improper handling and use, for example, poor spray technique, inadequate engineering controls and or lack of Personal Protective Equipment (PPE), may result in hazardous conditions or injury.
* Follow spray equipment manufacturer’s instructions to prevent personal injury or fire.
* Provide adequate ventilation for health and fire hazard control.
*
Follow company, product MSDS and respirator manufacturer’s recommendations for selection and proper use of respiratory protection. Be sure employees are adequately trained on the safe use of respirators per company and regulatory
requirements.
* Wear appropriate PPE such as eye and skin protection. In the event of injury, see first aid procedures on MSDS.
* Always observe all applicable precautions and follow good safety and hygiene for sale in California, Delaware or Maryland