Frigidaire 5304536607 Refrigerator Water Inlet Valve | Genuine OEM Part For Sale

Genuine OEM Single-Solenoid Water Inlet Control Valve (Replaces 5304529533)

🛑 STOP: Please contact us with your model number to verify compatibility before purchasing.

The Frigidaire 5304536607 (officially updating and replacing legacy factory part numbers 5304519215, 5304523078, and 5304529533) is a factory-original replacement single-solenoid water inlet valve for residential refrigerators. Mounted securely within the lower rear machine compartment chassis or behind the base kickplate grill, this genuine OEM electromechanical component acts as the primary gatekeeper regulating pressurized water flow into the appliance\'s ice-maker mold tray or water filtration lines.

As an Authentic Frigidaire Fluid-Control Component, this valve features an integrated electromagnetic solenoid coil, compression-style water port fittings, and a fine mesh internal sediment screen. When the refrigerator\'s control system triggers a fill cycle, a low-voltage electrical current is routed to the solenoid coil. This creates a magnetic field that lifts the internal spring-loaded rubber diaphragm, allowing pressurized water to flow into the designated water line. Opting for a genuine factory water valve ensures exact solenoid coil resistance parameters to prevent control board relay burnout, protects against sudden burst-pressure plumbing leaks, and matches the precise gallon-per-minute (GPM) flow design to prevent ice-maker mold overfills or underfills.

• Ice Maker Will Not Make Ice or Fill with Water: The ice maker cycles normally and the system is not locked out, but water never enters the mold tray because the valve\'s solenoid coil has failed or its internal filter screen is completely choked with sediment.
• Water Constantly Drips or Leaks into the Freezer: A slow, steady drip from the ice-maker fill tube causes a solid sheet of ice to form inside the ice bucket or down the freezer liner. This confirms the valve\'s internal spring-loaded rubber seal has worn out, torn, or failed to close completely.
• No Water Flowing from the Front Door Dispenser: Activating the dispenser paddle produces a faint electrical humming sound from the back of the fridge, but no water is delivered because the valve core has seized.
• Audible Shuddering, Chattering, or Loud Vibrating Noises: When the ice maker or dispenser cycles on, the lower cabinet emits a loud rattling or intense buzzing sound, indicating a failing or structurally fatigued solenoid coil armature.

• Part Number: 5304536607 (Replaces 5304519215, 5304523078, 5304529533)
• Part Type: Single-Solenoid Electromechanical Water Inlet Valve
• Electrical Interface: Low-Profile Spade Terminal Solenoid Connections
• Condition: Brand New, Genuine Frigidaire OEM Replacement Part
• Brand Compatibility: Precision engineered to fit select premium side-by-side, bottom-mount, and French-door refrigerators across the Frigidaire, Frigidaire Gallery, and Electrolux brand catalogs.

⚠️ WARNING: POTENTIAL RISK OF WATER DAMAGE AND ELECTRICAL SHOCK! This component sits at the intersection of household plumbing and electricity. **You must completely shut off the primary household water supply line feeding the refrigerator AND pull the primary electrical power utility plug away from the wall receptacle (or switch the dedicated circuit breakers to the absolute OFF position) before attempting this repair**. Keep an empty bucket and dry towels nearby to catch residual water standing inside the lines. **Always wear light work gloves and protective safety glasses throughout this procedure**. Pro Tip: Use Clean, Square Tubing Cuts and Avoid Over-Tightening! When connecting your existing plastic or copper water lines to your new **Frigidaire 5304536607** inlet valve, ensure the ends of the tubing are cut perfectly square and are free of burrs, scratches, or compression deformation. If the end of a plastic line is scored or crimped, **trim the end back cleanly using a sharp utility knife—never use wire cutters, or you will crush the line oval and cause a slow, continuous drip**. When tightening brass compression nut fittings, turn them strictly by hand until snug, then use two open-ended wrenches to turn the nut an additional 1/2 to 3/4 turn. **Never use high-torque power tools or over-torque compression ports**, as this will strip the threads or crack the valve\'s plastic housing. After completing the installation, turn the household water supply valve back on and wait at least 15 to 20 minutes to verify there is absolutely no weeping or moisture bridging at any fitting before sliding the appliance back into position. Installation Steps: Fully isolate all incoming electrical power and water supplies. Pull the refrigerator away from the wall to access the lower rear panel. Unbolt the screws securing the lower rear machine compartment access cover and remove the shroud. Locate the water inlet valve near the base. Place a shallow tray or towel underneath the water connections. Unthread the incoming water supply line from the valve fitting. Matching your existing configuration, disconnect the internal plastic water lines feeding the cabinet by depressing the collar on the quick-connect fittings and pulling the tubes straight out. Carefully pull the wire harness terminal connectors off the solenoid spade terminals. Unbolt the mounting screw securing the valve bracket to the frame and pull the old valve clear. Position your brand-new genuine replacement water valve, hand-drive the mounting bracket screw to secure it to the frame, and plug the electrical wires back onto the solenoid terminals. Insert the plastic water tubes firmly into the quick-connect ports until they bottom out and lock securely. Re-attach the primary water supply line to the inlet port, tightening it by hand and snugging it with a wrench. Slowly open the main water supply valve to check for leaks. Re-secure the rear access panel cover, restore electrical utility power, and verify smooth, leak-free ice and water dispensing cycles.

** Please contact us with your model number to verify compatibility before purchasing. **