Ten Second Color Acetone Based Stain *24 Color Options*- 32oz & 1 Gallon Bottles For Sale

Ten Second Color™ Acetone-Based Concrete Stain

Create rich, professional-looking color in seconds with Ten Second Color™ (TSC) Acetone-Based Concrete Stain. This fast-drying, penetrating concrete dye produces beautiful translucent, mottled color similar to acid stain—without waiting for a chemical reaction.

TSC penetrates properly prepared concrete and dries quickly, making it an excellent choice for decorative concrete floors, patios and other cementitious surfaces. Colors can be applied individually, layered or blended to create custom effects with depth and natural variation.

Why Choose Ten Second Color?

• Fast-drying color in seconds

• Creates mottled, acid-stain-like effects

• 24 colors from natural neutrals to bold accent colors

• Translucent color lets the character of the concrete show through

• Colors can be layered and blended

• Approximately 100–150 sq. ft. coverage per quart

• Approximately 400–600 sq. ft. coverage per gallon

• For interior and exterior concrete

• Professional-grade penetrating concrete dye

• Ideal for use with an acetone-compatible ReCharger Sprayer

Just Add Acetone & Apply

TSC is supplied as concentrated pigment and MUST be mixed with acetone before application.

32 oz size: Add 32 oz of acetone
Makes approximately 2 quarts of ready-to-apply stain

1 gallon size: Add 1 gallon of acetone to the pre-measured pigment
Makes approximately 1 gallon of ready-to-apply stain

Acetone is not included and must be purchased locally.

Fast Color. Endless Possibilities.

Use a single color for a clean, contemporary finish or layer multiple TSC colors to create marbled, variegated and custom decorative effects. Because TSC is translucent, the natural texture and variation of the concrete remain part of the finished look.

Always test your selected color on the actual concrete before completing the entire project. Concrete condition, porosity, preparation and application technique can affect the final appearance.

Coverage:

One quart TSC Dye covers an average of 100-150 sq ft.
One gallon TSC Dye covers an average of 400-600 sq ft.
Coverage variations depend on concrete surface porosity and amount of material applied.

Color Test- Apply a test sample of TSC Dye in an inconspicuous area of the floor to verify color. Use the same application method for the test spot as what is planned for the entire floor.
Mixing
***ACETONE MUST BE ADDED TO DYE**
32 OUNCES CONTAINER: MIX 32 ounces of acetone to under filled jars of TSC dye..

Surface Prep:Step 1: If needed, remove all paint and/or sealer from the surface using CR-590 Paint & Sealer Remover.
Step 2: If the surface has an oily or greasy film OR if CR-590 Paint & Sealer Remover was used, scrub the surface using CR-580 Degreaser.
Step 3: (REQUIRED) Use mechanical means to open up the pores of the concrete (Grinding, Black Pad, Sanding Screen or Coatings Removal Pad for Interior Slabs or Pressure Washer for Exterior Slabs) or apply CR-765 Surface Prep & Etch at a dilution ratio of 4 parts water to 1 part Surface Prep & Etch. Scrub in with a stiff bristle broom. When the fizzing action stops, rinse the surface with water. Do not allow the Surface Prep & Etch solution to dry on the concrete. If a more porous surface is needed repeat Step 3. An interior floor’s surface texture should feel similar to 120 grit sand paper.
Step 4: (REQUIRED) If acid etching, you must apply CR-585 Surface Neutralizer (dilution of 8 oz in 5 gallons water) using a stiff bristle brush or broom to scrub in the neutralizing solution then rinse with water.Application:

CAUTION: Acetone is Flammable - Do not use any form of electrical equipment to mix the dye with the acetone. Refer to MSDS for exposure limitations and safe handling practices.

Application: Concrete substrate MUST be clean and dry before applying TSC Dye. Apply TSC Dye with a cone tip pump sprayer that is compatible with acetone. Keep the tip approximately 24 inches from the surface. Apply in a uniform circular motion, not allowing product to puddle in low spots. The concrete surface should appear wet for just a few seconds when applied properly. TSC Dye can also be applied with a brush, roller or HVLP spray equipment. Properly evaluate each job to determine the best method of application.
TSC Dye may leave residual dye on the surface after each application. Vacuum loose dye prior to sealer application. The use of water to clean and remove loose dye is NOT recommended.
When spraying TSC Dye, protect surroundings with masking paper or masking plastic.

Sealing:It is strongly recommended that a clear sealer be applied as a top coat for abrasion and UV resistance. It is recommended that a non-skid / skid reducer be utilized when sealing exterior surfaces.
Seal surface with a low viscosity, sprayable sealer. Use appropriate sprayer and tip per individual sealer instructions. If applying with a roller, do not overwork sealer as it may reactivate the dye.
Floor Finish –When using a floor finish, allow sealer to dry and completely cure for 3-4 days.